Lasko MyHeat-GO CD12100 13-inch Ceramic Heater review

The Lasko MyHeat-GO CD12100 is a tabletop ceramic heater with a higher power ceiling and more controls than Lasko’s tiny personal warmers. Its single Black SKU offers two heat settings and an adjustable thermostat, but it is still a supervised indoor appliance with unusually important placement and outlet rules. The “13-inch” label describes its class; Lasko lists a 12.9-inch body height.

Tabletop shape, full-size heater input

Lasko lists 900–1,500 watts at 120 volts and two heat settings. That makes this a different electrical proposition from a 200- or 400-watt desk warmer, even though Lasko calls it a compact table heater. The manufacturer also lists 7.5–12.5 amps. Treat those as the maker’s electrical figures, not a promise about room temperature, heating speed or operating cost. The page’s “up to 100 square feet” coverage is a manufacturer claim, not an independent room test. If your decision depends on a small-power limit, use the listed maximum of 1,500 watts rather than relying on the product’s compact footprint.

The published body measures 12.9 inches high, 7.42 inches wide and 4.06 inches deep. The page says 3.0 pounds, while the native variant record carries a raw weight value of 1,814 without a stated unit. Because those records do not reconcile, confirm weight directly if lifting ease is a deciding factor. A six-foot cord and carry handle help with moving the appliance, but neither changes the outlet and clearance requirements below.

Two heat choices, one adjustable thermostat

The front controls separate a Low/High heat switch from the thermostat dial. The Rev. A 05/23 instructions describe setting the thermostat, allowing the heater to warm the room, then lowering the dial until heat stops; the thermostat then cycles the heater around the selected comfort point. They do not publish a Fahrenheit range or temperature-accuracy figure. They also do not clearly say whether automatic cycling is available on both Low and High, so a requirement for a specific thermostat stage is not confirmed.

Lasko advertises oscillation and the manual includes a separate oscillation switch. The product material does not specify a sweep angle or identify an axis. That means the general oscillation feature is real, but I would not use it to satisfy a must-have horizontal angle or two-axis movement requirement. It is not a fan-only appliance: no separate fan-only mode is listed. The page also lists no remote, phone app, timer, countdown shutoff, adjustable tilt or control lock. “Quiet” is promotional wording, not a measured sound level.

Make the operating plan work before choosing controls

The exact manual is the main fit screen. It calls the CD12100 residential-use only and says to put it on a stable, flat, level surface. Keep combustible items at least three feet in front and one foot away from the sides and rear. Those are operating clearances, not simply the heater’s body dimensions. A table beside papers, curtains, bedding or a chair may leave too little open space even if the heater itself fits.

Plug it directly into a 120-volt wall receptacle. The manual prohibits extension cords, power strips, surge protectors, outlet adapters, cord reels and other devices on the same outlet or circuit. It also says not to leave the heater running unattended. Bathrooms, laundry areas, damp or wet locations and outdoor use are excluded; never place it where it could fall into water. If your planned location or routine conflicts with one of those instructions, select a different heater and setup rather than treating the thermostat or an overheat protector as permission to take a shortcut.

Thermal protection is not a timer

The product specification says “No Auto Shut Off” and “No Timer.” The manual does describe a thermal-overload protector: after an overheat event it shuts the unit down, and the owner must unplug it, let it cool for ten minutes and reset it. That is a protective response to overheating, not a countdown feature or scheduled start. It does not change the no-unattended instruction. The listed cool-touch housing is also a manufacturer claim, not a reason to touch hot surfaces or reduce required clearances.

Who should consider the CD12100?

It makes sense for someone who wants a manually controlled tabletop heater with two heat choices, thermostat cycling and an advertised oscillation function, has access to a suitable direct wall outlet, and can keep the full clear zone while attending it. In the finder, the documented positive path is indoor tabletop use, at least two heat levels, an adjustable thermostat and a 1,500-watt maximum allowance. Do not select horizontal or two-axis oscillation as an essential condition based on the generic oscillation label alone; the published sources do not establish the axis.

For a simpler, much lower listed input, compare the MyHeat Mini 200/201, which is a one-setting 400-watt tabletop heater without a thermostat. If an automatic shutoff countdown matters more, compare the MyHeat Max CD09100; the related CD09101 adds a documented tip-over switch. Those alternatives have their own instructions and restrictions, so check their individual reviews rather than assuming that one control or safety feature makes a heater suitable for unattended operation.

For setup and maintenance, vacuum the CD12100’s intake grilles every two weeks, unplug it before moving or cleaning, and do not disassemble or immerse it. Lasko lists a three-year limited warranty for the original purchaser. Review the current CD12100 product page and the linked Rev. A 05/23 instructions before use.